Dechuang Products
Product Search
Welcome to the DeChuang search function
products you are here:Home -> DCM Servo Energy-efficient Sil
Product:
DCM-120 Servo Energy efficient Silicone Injection Machine
Categories: DCM Servo Energy-efficient Sil Manufacturer: Guangzhou DeChuang
Categories: DCM Servo Energy-efficient Sil Manufacturer: Guangzhou DeChuang
The machine is controlled by a servo control system, which helps increase dynamic response and torque density to the highest level and which replaces the tradition mode of driving that may adopt a hydraulic, dc, stepping, or frequency control mechanism. Such a configuration enables the system to have a shorter cycle, a higher production rate, better reliability and a longer service life. The entire servo system consists of a servo driver, a servomotor, an encoder and a load, which together run in one control closed-loop system. Within the system, the driver receives information from the outside, and then transmits it to the servomotor, which converts the current into a torque and then passes it on to the load.
Upon receipt of the torque, the load acts or accelerates or decelerates or decelerates automatically, depending on its own characteristics. The encoder measures the position of the servomoter and feeds the signal generated back to the driver. Furthermore, the encoder is a high-precision controller and can transmit modified values to the servo driver automatically, whereas the driver retroacts the set values. The entire system functions as a high-responsive closed-loop system. The DCM silica gel injection machine can save electricity by 40-80%, depending on the specific type of product. Normally, the thicker the glue layer of a product and the longer the cooling time, the less the electricity required.
1. Quicker response and higher precision.
2. A shorter forming cycle and higher efficiency
3. Lower energy consumption on the part of the motor
4. The current generated when starting a conventional motor is generally 5 times as high as that maintained when in normal operation. Because a DCM machine adopts soft start, it will not cause impact to the power grid;
5. More water and oil-efficient
6. Lower noise
7. A shorter machine body
8. A higher cost-performance ratio
Upon receipt of the torque, the load acts or accelerates or decelerates or decelerates automatically, depending on its own characteristics. The encoder measures the position of the servomoter and feeds the signal generated back to the driver. Furthermore, the encoder is a high-precision controller and can transmit modified values to the servo driver automatically, whereas the driver retroacts the set values. The entire system functions as a high-responsive closed-loop system. The DCM silica gel injection machine can save electricity by 40-80%, depending on the specific type of product. Normally, the thicker the glue layer of a product and the longer the cooling time, the less the electricity required.
1. Quicker response and higher precision.
2. A shorter forming cycle and higher efficiency
3. Lower energy consumption on the part of the motor
4. The current generated when starting a conventional motor is generally 5 times as high as that maintained when in normal operation. Because a DCM machine adopts soft start, it will not cause impact to the power grid;
5. More water and oil-efficient
6. Lower noise
7. A shorter machine body
8. A higher cost-performance ratio
|
Specification table for the DCM servo energy-efficient silica gel injection machine
|
|||||||||||||
|
Model
|
Units
|
|
|
|
|
||||||||
|
screw diameter
|
mm
|
Ø28
|
|
Ø36
|
Ø40
|
Ø40
|
|
Ø45
|
Ø50
|
||||
|
injection pressure
|
Kg/cm2
|
2321
|
1777
|
1944
|
1575
|
2083
|
1645
|
2292
|
1856
|
||||
|
injection rate
|
cm3/sec
|
70
|
92
|
106
|
131
|
135
|
170
|
138
|
170
|
||||
|
screw stroke
|
mm
|
140
|
160
|
185
|
215
|
||||||||
|
theoretical volume
|
cm3
|
86
|
112
|
163
|
200
|
232
|
294
|
341
|
422
|
||||
|
clamping force
|
T
|
68
|
92
|
120
|
167
|
||||||||
|
demolding stroke
|
mm
|
450
|
500
|
560
|
640
|
||||||||
|
minimum mold thickness
|
mm
|
150
|
180
|
200
|
220
|
||||||||
|
maximum demolding distance
|
mm
|
600
|
730
|
760
|
860
|
||||||||
|
space between tie bars
|
mm
|
320*320
|
360*360
|
425*425
|
460*460
|
||||||||
|
Ejector force
|
T
|
2.7
|
3.3
|
3.9
|
5.3
|
||||||||
|
Max hydraulic pressure
|
Kg/cm2
|
140
|
140
|
140
|
140
|
||||||||
|
Motor power
|
KW
|
7.5
|
11
|
15
|
18.5
|
||||||||
|
Machine weight
|
T
|
2.7
|
3.6
|
4.5
|
6
|
||||||||
|
Machine dimension (L*W*H)
|
m
|
4.1*0.9*1.5
|
4.2*1.3*1.6
|
5.1*1.0*1.6
|
5.5*1.0*1.7
|
||||||||
|
20/200Kg feeding machine
|
Weight
|
500Kg
|
Size
|
m
|
1.3*1.22*1.85/2.65
|
||||||||
|
20Kg feeding machine
|
Weight
|
350Kg
|
Size
|
m
|
1.2*1.0*1.9
|
||||||||
